Uta Klement
Uta Klement
Verified email at chalmers.se
Cited by
Cited by
Thermal stability of nanocrystalline Ni
U Klement, U Erb, AM El-Sherik, KT Aust
Materials Science and Engineering: A 203 (1-2), 177-186, 1995
Alloy design for intrinsically ductile refractory high-entropy alloys
S Sheikh, S Shafeie, Q Hu, J Ahlström, C Persson, J Veselý, J Zýka, ...
Journal of applied physics 120 (16), 164902, 2016
Thermal stability of electrodeposited nanocrystalline Co-1.1 at.% P
P Choi, M da Silva, U Klement, T Al-Kassab, R Kirchheim
Acta Materialia 53 (16), 4473-4481, 2005
On the generation of new orientations during recrystallization: recent results on the recrystallization of tensile-deformed fcc single crystals
A Berger, PJ Wilbrandt, F Ernst, U Klement, P Haasen
Progress in Materials Science 32 (1), 1-95, 1988
Oxide dispersion strengthened mechanically alloyed amorphous Zr-Al-Cu-Ni composites
J Eckert, M Seidel, A Kübler, U Klement, L Schultz
Scripta materialia 38 (4), 595-602, 1998
Cutting temperatures during hard turning—Measurements and effects on white layer formation in AISI 52100
SB Hosseini, T Beno, U Klement, J Kaminski, K Ryttberg
Journal of Materials Processing Technology 214 (6), 1293-1300, 2014
Formation mechanisms of white layers induced by hard turning of AISI 52100 steel
SB Hosseini, U Klement, Y Yao, K Ryttberg
Acta Materialia 89, 258-267, 2015
Thermal stability of nanostructured electrodeposits
GD Hibbard, U Erb, KT Aust, U Klement, G Palumbo
Materials Science Forum 386, 387-396, 2002
X-ray photoelectron spectroscopy studies of indium tin oxide nanocrystalline powder
B Pujilaksono, U Klement, L Nyborg, U Jelvestam, S Hill, D Burgard
Materials Characterization 54 (1), 1-7, 2005
Effect of build geometry on the microstructural development of 316L parts produced by additive manufacturing
A Leicht, U Klement, E Hryha
Materials Characterization 143, 137-143, 2018
Electrodeposited nanocrystalline Co–P alloys: microstructural characterization and thermal stability
M da Silva, C Wille, U Klement, P Choi, T Al-Kassab
Materials Science and Engineering: A 445, 31-39, 2007
Investigation of micro-textured cutting tools used for face turning of alloy 718 with high-pressure cooling
NT Alagan, P Zeman, P Hoier, T Beno, U Klement
Journal of Manufacturing Processes 37, 606-616, 2019
Effect of process parameters on the microstructure, tensile strength and productivity of 316L parts produced by laser powder bed fusion
A Leicht, M Rashidi, U Klement, E Hryha
Materials Characterization 159, 110016, 2020
Accelerated oxidation in ductile refractory high-entropy alloys
S Sheikh, MK Bijaksana, A Motallebzadeh, S Shafeie, A Lozinko, L Gan, ...
Intermetallics 97, 58-66, 2018
Comparison of the microstructures in continuous-cooled and quench-tempered pre-hardened mould steels
H Hoseiny, U Klement, P Sotskovszki, J Andersson
Materials & Design 32 (1), 21-28, 2011
Preparation of Mn, Fe and Co based perovskite catalysts using microemulsions
M Wallin, N Cruise, U Klement, A Palmqvist, M Skoglundh
Colloids and Surfaces A: Physicochemical and Engineering Aspects 238 (1-3 …, 2004
Characterization of the surface integrity induced by hard turning of bainitic and martensitic AISI 52100 steel
SB Hosseini, K Ryttberg, J Kaminski, U Klement
Procedia CIRP 1, 494-499, 2012
Microstructural characteristics of Alloy 718 and Waspaloy and their influence on flank wear during turning
P Hoier, A Malakizadi, P Stuppa, S Cedergren, U Klement
Wear 400, 184-193, 2018
Effect of∑ 2 grain boundaries on plastic deformation of WC–Co cemented carbides
G Östberg, MU Farooq, M Christensen, HO Andrén, U Klement, ...
Materials Science and Engineering: A 416 (1-2), 119-125, 2006
Characterization and dielectric properties of β-SiC nanofibres
Y Yao, A Jänis, U Klement
Journal of materials science 43 (3), 1094-1101, 2008
The system can't perform the operation now. Try again later.
Articles 1–20