che hassan che haron
che hassan che haron
Professor of Manufacturing, Universiti Kebangsaan Malaysia
Verified email at
Cited by
Cited by
The effect of machining on surface integrity of titanium alloy Ti–6% Al–4% V
CH Che-Haron, A Jawaid
Journal of materials processing technology 166 (2), 188-192, 2005
Tool life and surface integrity in turning titanium alloy
CH Che-Haron
Journal of Materials Processing Technology 118 (1-3), 231-237, 2001
Tool wear characteristics in turning of titanium alloy Ti-6246
A Jawaid, CH Che-Haron, A Abdullah
Journal of Materials Processing Technology 92, 329-334, 1999
Initiating automotive component reuse in Malaysia
L Amelia, DA Wahab, CHC Haron, N Muhamad, CH Azhari
Journal of Cleaner Production 17 (17), 1572-1579, 2009
Tool wear and surface integrity of inconel 718 in dry and cryogenic coolant at high cutting speed
AH Musfirah, JA Ghani, CHC Haron
Wear 376, 125-133, 2017
Surface integrity of Inconel 718 when finish turning with PVD coated carbide tool under MQL
MZA Yazid, CH CheHaron, JA Ghani, GA Ibrahim, AYM Said
Procedia Engineering 19, 396-401, 2011
Wear of coated and uncoated carbides in turning tool steel
CHC Haron, A Ginting, JH Goh
Journal of materials processing technology 116 (1), 49-54, 2001
Wear mechanism and notch wear location prediction model in ball nose end milling of Inconel 718
MS Kasim, CHC Haron, JA Ghani, MA Sulaiman, MZA Yazid
Wear 302 (1-2), 1171-1179, 2013
Investigation on the influence of machining parameters when machining tool steel using EDM
CHC Haron, BM Deros, A Ginting, M Fauziah
Journal of Materials Processing Technology 116 (1), 84-87, 2001
Performance of alloyed uncoated and CVD-coated carbide tools in dry milling of titanium alloy Ti-6242S
CHC Haron, A Ginting, H Arshad
Journal of Materials Processing Technology 185 (1-3), 77-82, 2007
Surface roughness prediction model of 6061-T6 aluminium alloy machining using statistical method
K Kadirgama, MM Noor, MM Rahman, MRM Rejab, CHC Haron, ...
Euro Journals, 2009
Monitoring online cutting tool wear using low-cost technique and user-friendly GUI
JA Ghani, M Rizal, MZ Nuawi, MJ Ghazali, CHC Haron
Wear 271 (9-10), 2619-2624, 2011
Development and testing of an integrated rotating dynamometer on tool holder for milling process
M Rizal, JA Ghani, MZ Nuawi, CHC Haron
Mechanical systems and signal processing 52, 559-576, 2015
Online tool wear prediction system in the turning process using an adaptive neuro-fuzzy inference system
M Rizal, JA Ghani, MZ Nuawi, CHC Haron
Applied Soft Computing 13 (4), 1960-1968, 2013
Effect of chilled air on tool wear and workpiece quality during milling of carbon fibre-reinforced plastic
MKN Khairusshima, CHC Hassan, AG Jaharah, AKM Amin, ANM Idriss
Wear 302 (1-2), 1113-1123, 2013
Application of Taguchi method in the optimization of turning parameters for surface roughness
G Akhyar, CH Che Haron, JA Ghani
International Journal of Science Engineering and Technology 1 (3), 60-66, 2008
The effect of dry machining on surface integrity of titanium alloy Ti-6Al-4V ELI
GA Ibrahim, CHC Haron, JA Ghani
Journal of applied sciences 9 (1), 121-127, 2009
Copper and graphite electrodes performance in electrical-discharge machining of XW42 tool steel
CHC Haron, JA Ghani, Y Burhanuddin, YK Seong, CY Swee
journal of materials processing technology 201 (1-3), 570-573, 2008
Failure mode analysis of carbide cutting tools used for machining titanium alloy
JA Ghani, CHC Haron, SH Hamdan, AYM Said, SH Tomadi
Ceramics International 39 (4), 4449-4456, 2013
Cutting tool wear classification and detection using multi-sensor signals and Mahalanobis-Taguchi System
M Rizal, JA Ghani, MZ Nuawi, CHC Haron
Wear 376, 1759-1765, 2017
The system can't perform the operation now. Try again later.
Articles 1–20