Follow
MOHD FADZIL ABDUL RAHIM, PhD
MOHD FADZIL ABDUL RAHIM, PhD
Senior Lecturer, Faculty of Mechanical Engineering
Verified email at ump.edu.my
Title
Cited by
Cited by
Year
Experimental investigation and development of new correlation for thermal conductivity and viscosity of BioGlycol/water based SiO2 nanofluids
MK Abdolbaqi, NAC Sidik, MFA Rahim, R Mamat, WH Azmi, ...
International Communications in Heat and Mass Transfer 77, 54-63, 2016
452016
Comparative evaluation of a two stroke compressed natural gas mixer design using simulation and experimental techniques
D Ramasamy, RA Bakar, MF Rahim, MM Noor
Proceedings of the 4th IASTED Asian Conference on Power and Energy Systems …, 2008
232008
Heat transfer characteristics in exhaust port for hydrogen fueled port injection engine: a transient approach
M Rahman, KI Hamada, MM Noor, K Kadirgama, RA Bakar, MFA Rahim
Advanced Materials Research 152, 1909-1914, 2011
102011
CFD prediction of heat and fluid flow through U-bends using high Reynolds-number EVM and DSM models
MF Ghazali, MFA Rahim
Procedia Engineering 53, 600-606, 2013
52013
Effect of injection pressure, injection duration, and injection frequency on direct injector’s mass flow rate for compressed natural gas fuel
MHR Alias, MFA Rahim, MHMI Rodzi, RA Bakar
MATEC web of conferences 225, 02008, 2018
42018
Parametric Study of CNG-DI Engine Operational Parameters by Using Analytical Vehicle Model
MFA Rahim, AA Jaafar, R Mamat, Z Taha
Proceedings of the International Manufacturing Engineering Conference & The …, 2019
22019
Effect Of Engine Speed On Common Rail Injection System For Hydrogen Engine
M Kamil, MM Rahman, RA Bakar, MFA Rahim, MM Noor
National Conference in Mechanical Engineering Research and Postgraduate …, 2010
22010
Single hole direct injector simulation validation and parametric sensitivity study
MHR Alias, MFA Rahim, RA Bakar
IOP Conference Series: Materials Science and Engineering 788 (1), 012063, 2020
12020
Effect of Heat Transfer on Cylinder Wall During Cooling Process Using Computational Fluid Dynamic
RA Bakar, Mohd. Fadzil Abdul Rahim, LM Gan
Universiti Teknologi Malaysia, 2003
12003
Flow Analysis of New Two-stroke Engine Design Using Computational Fluid Dynamic
RA Bakar, RA Bakar, KL Chin, Mohd. Fadzil Abdul Rahim, LM Gan
Universiti Teknologi Malaysia, 2003
12003
Optimization of CNG Direct Injector Parameters Using Model-Based Calibration Framework
MHR Alias, MFA Rahim, RA Bakar
Recent Trends in Mechatronics Towards Industry 4.0, 917-929, 2022
2022
Simulation study on the effect of fuel injection and air intake boundary setup on the brake torque response by using comprehensive vehicle model for natural gas vehicle (NGV)
MFA Rahim, AA Jaafar, Z Taha, R Mamat
IOP Conference Series: Materials Science and Engineering 863 (1), 012001, 2020
2020
Performance assessment of direct injection compressed natural gas vehicle at different injection pressures using speed-sweep test method
MFA Rahim, AA Jaafar, R Mamat, Z Taha, MHR Alias
IOP Conference Series: Materials Science and Engineering 788 (1), 012068, 2020
2020
The conference had brought a new outlook on cutting-edge issues shared through the keynote speeches by Assoc. Prof. Dr. Han-Lim Choi (Korea Advanced Institute of Science and …
Z Ismail, AC Benedict, N Ahmad, K Muthusamy, MIM Khairuddin, ...
In Cylinder Pressure Analysis of Two-Stroke Spark Ignition Engine
RA Bakar, NMIN Ibrahim, ARI Semin, MFA Rahim, I Ali
SWIRL DEVICE CHARACTERSTIC ANALYSIS IN INTAKE MANIFOLD
RA Bakar, AA Aziz, CK Leong, MF Abd Rahim, D Ramasamy
Numerical Analysis of in-Cylinder Process for Small Two-Stroke Spark-Ignition (SI) Engine
RA Bakar, N Ibrahim, MFA Rahim, I Ali
The system can't perform the operation now. Try again later.
Articles 1–17